FAQ SIEMENS
What is the meaning of SINORIX?
SINORIX stands for "Siemens No Risk".
Does the adoption of a machine tool protection system allow me to work in an unmanned area?
Absolutely yes, SIEMENS SINORIX al-deco object protection systems are business continuity systems. They allow not only to work safely in the unmanned, but in case of an accident not to lose production capacity.
Does the adoption of an object protection system decrease my Fire load?
No, the total fire load does not decrease if the compliant solutions are used, because the rules, also in the new Ministerial Decree 05.08.2015 "New Fire Protection Code", do not consider automatic protection systems. But in the case of the use of FSE modelling, then chapter M.2.6 shows that it is possible to consider a fire curve with a release of energy (RHR vs Time curve) very low compared to traditional solutions to the advantage of much cheaper solutions for the fulfilment of legal obligations.
Does the activation of the system leave residues that can damage the machine?
NO, absolutely. The use of natural gases for extinguishing (CO2, Argon, Nitrogen etc) leaves no residue, there is no risk of damaging the machine due to extinguishing and / or pollution of the cooling lubricant.
Is my machine connected to a fume extraction system I have to have some precautions?
It depends, if the system is a centralized system, then it is mandatory to install an intake closing damper that activates with the system. If instead the machine is connected to a dedicated suction system, just make sure that with the activation of the machine emergency the power to the aspirator is cut so that it stops by inertia.
Should the sensor be replaced anyway?
In most cases the sensor is never replaced throughout the life of the system. Then it depends on case by case.
Do you need special attention on the machine or in its vicinity to prevent the system from accidentally activating?
No, the detection system is a physical sensor and therefore is not affected by any mechanical and / or electromagnetic interference, and is insensitive to the degradation of oil or dirt.
Do these systems need maintenance?
Being security systems, the law provides that they must be checked every 6 (six) months by specialized personnel, but the system itself does not require any daily and / or periodic maintenance except for an annual check of the correct functionality of the signals.
What happens if the power is missing?
Nothing, the SINORIX al-deco system works anyway because the detection and activation are pneumatic and do not require power and the fire itself is the activator of the system. The electronics are used to monitor system efficiency and record events.
How long does the system intervene in the event of a fire?
The LIFDES sensor is a linear heat sensor that melts at 110 ° C the intervention time depends on how fast the temperature increases and is obviously a function of the sensor distance from the flame origin and is influenced by the presence or absence of the system fumes suction, however, it is a matter of intervention times of a few seconds.
Can I Install SINORIX on any machine tool?
Yes, SINORIX al-deco uses clean contacts to communicate with the machine and is therefore independent of the type of CN installed on the machine.
FAQ NOP
NOP self-filtering pumps can be installed on any machine tool ?
In theory Yes, the restrictions are due to the kind of fluid that is used (there are limits due to the viscosity according to the degree of filtration desired) for more details refer to the manual of the single pump available area "download”
I do not have any room available into the coolant tank, How can I do?
NOP developed self-standing versions of pumps with medium and high pressure. that does not require any modification of your current tank.
How long shall I clean and maintenance the filter?
YTH pumps do not require maintenance in general and therefore filter neither need to be cleaned nor replaced. "Ex" version it may be that the insoluble oil (e.g. lubrication of guideline) can obstruct the net filter, but it is enough to carry out the counter wash procedure to restore the original situation.
Can I install TAZUNA on the machine tools present in my shop floor?
Yes of course, Tazuna is a “Plug & Play” solution, with very light effort your maintenance service is able to install it on any of the machine tools pressure modulation is required. Of course Tazuna works with YTH Pumps only.